Well Pump Keeps Running? Causes to Check and When to Call

November 16, 2026

Pressure gauge and pressure switch on a private well system in North Texas

By Robert Reagan, CEO, Flowcore Water
Licensed Texas water well contractor serving North Texas since 2006.
Published November 2026 · Last updated November 2026

A well pump should run, build pressure and rest. When the well pump keeps running long after everyone has turned off the taps, something is either drawing water you cannot see, or the system cannot reach the pressure that tells the pump to stop. Left alone, a pump that never rests wears out early and runs up the electric bill.

This guide walks through the common causes in the order worth checking, from the free ones to the ones that need a technician. If you would rather have it diagnosed, book a well repair visit with Flowcore or call (817) 480-7971.

Why Does My Well Pump Keep Running?

A well pump keeps running when the pressure switch never sees the cut-off pressure. That happens when water is leaking out somewhere, when the pump cannot deliver enough water to build pressure, or when the pressure switch itself has failed or is set too high. FreshWater Systems' October 2026 troubleshooting guide lists high demand, a faulty pressure switch, low water levels, a damaged pump and leaks as the main causes.

This is a different problem from a pump that starts and stops on its own or trips the breaker. If the pump runs and then cuts out, our guide on why a well pump keeps shutting off covers that side.

Causes to Check, From Simplest to Most Serious

1. Water is still being used somewhere

Before blaming the pump, make sure nothing is drawing water: a running toilet, a dripping outdoor spigot, an irrigation zone stuck open, a water softener in regeneration or a livestock waterer with a stuck float. FreshWater Systems notes that a running toilet or hidden leak can keep the pump running on its own. Checking every fixture first costs nothing and rules out the simplest explanation.

2. A leak between the well and the house

A leak in the line from the well to the pressure tank can stop the system from ever reaching shut-off pressure. Hunker's troubleshooting guide points to wet spots in the yard along the water line as a clue, and to corroded galvanized pipe in older systems as a common source.

One way to narrow it down is to close the valve on the house side of the pressure tank. If the pressure still drops while nothing in the house can draw water, the loss is between the well and the tank, or down in the well itself.

3. A pressure switch that is stuck or set too high

The pressure switch turns the pump on and off based on system pressure. FreshWater Systems explains that a bad switch can signal the pump to run when it should not. Burned or welded contacts can hold the pump on, and a switch set above what the pump can produce will never reach its cut-off.

The switch carries line voltage next to water, so adjustments and replacements belong with a technician. Hunker's troubleshooting guide gives the same advice for that reason.

4. The water level in the well has dropped

When the water level falls, the pump may not get enough water to keep up. FreshWater Systems notes that low water levels can leave the pump running to fill the tank while little water actually reaches it. Running a pump with too little water can damage it, so this cause is worth confirming quickly, especially late in a dry summer.

5. A worn or damaged pump

A pump with worn impellers can still move water, just not enough to build full pressure. FreshWater Systems describes a damaged pump that cannot pump water at the proper flow rate, so it never builds enough pressure to shut off. A broken drop pipe or a failed check valve down the well can produce similar symptoms, which is why the pump is often pulled to confirm.

Is It Bad for a Well Pump to Run Constantly?

It is bad for a well pump to run constantly. FreshWater Systems warns that a pump left running too long can become damaged, and constant operation shows up as higher electric bills. A pump running without enough water is at even greater risk of damage.

If the pump will not stop and you cannot find an obvious leak, turning off the pump's breaker until it can be checked protects the motor. Keep a few gallons of water on hand for the meantime.

When to call for a diagnosis

Call for a diagnosis when the house shows no leaks and the pump still runs, when pressure at the tank gauge stays well below the switch's cut-off setting, or when the problem started after a dry spell. A technician can measure the pump's output, check the switch and pull the pump if needed, which avoids replacing parts that were not the problem.

Before the visit, note what the pressure tank gauge reads while the pump is running and whether the pump ever stops on its own. Those two details help narrow the cause quickly and can save time on site.

Repair or Replace the Pump?

Whether to repair or replace depends on what failed. A switch, a leak in the line or a waterlogged pressure tank are repairs. A pump that can no longer produce enough flow is usually a candidate for replacement. When the pump itself is the problem, our well pump replacement service covers sizing and installing the right unit for your well.

A pressure tank that has lost its air charge can also make the pump work harder than it should. Our guide to pressure tank replacement cost explains when the tank is part of the problem.

We diagnose pumps that will not shut off across North Texas, including Haslet and the surrounding area, and handle everything from a switch swap to a complete pump replacement.

Frequently Asked Questions About a Well Pump That Won't Shut Off

How long should a well pump run at a time?

A well pump should run only long enough to refill the pressure tank to the switch's cut-off pressure, then rest until pressure falls to the cut-in point. The exact time depends on the pump, the tank size and how much water is in use, so a pump that runs with no water in use at all points to a leak or a fault.

Can a bad pressure switch make the pump run nonstop?

A bad pressure switch can make a well pump run nonstop. FreshWater Systems notes that a faulty switch can signal the pump to run when it should not, and burned or stuck contacts can keep power to the motor. Because the switch carries line voltage, testing and replacing it is a job for a technician.

Should I turn off a well pump that won't stop running?

Turning off a well pump that will not stop running is a sensible way to protect it until it is checked, especially if no water is in use. FreshWater Systems warns that a pump left running too long can be damaged, so switching off its breaker can prevent a repair from turning into a replacement.

"It runs for hours and then stops and needs to be reset." If that sounds like your well, call (817) 480-7971 or send us what the pump is doing, and our well repair technicians will find the cause before replacing anything.

Call Now (817) 480-7971